Stk413-430 Circuit Diagram -

[ A_v = 1 + \fracR_fR_in ]

This is a technical request regarding the series, which are thick-film hybrid integrated circuits (Hybrid ICs) manufactured by Sanyo (now part of ON Semiconductor). These ICs are dual-channel audio power amplifiers, commonly found in stereo systems, home theater receivers, and musical instrument amplifiers from the 1980s to early 2000s. stk413-430 circuit diagram

| Pin | Symbol | Function | | :--- | :--- | :--- | | 1 | INPUT (+) | Non-inverting input, Channel 1 | | 2 | INPUT (-) | Inverting input / Feedback, Channel 1 | | 3 | GND | Signal Ground | | 4 | INPUT (-) | Inverting input / Feedback, Channel 2 | | 5 | INPUT (+) | Non-inverting input, Channel 2 | | 6 | +Vcc | Positive Power Supply (Main) | | 7 | OUTPUT | Channel 2 Output | | 8 | -Vcc | Negative Power Supply | | 9 | GND | Power Ground | | 10 | OUTPUT | Channel 1 Output | | 11 | +Vcc | Positive Power Supply (Pre-driver) | | 12 | BOOT | Bootstrap (Channel 1) | Note: The exact pin function may swap channels (1/2) depending on manufacturer datasheet revision. Always verify against your IC's specific datasheet. Below is a unified schematic representing typical stereo application for STK4132, STK430, STK432, etc. [ A_v = 1 + \fracR_fR_in ] This

+Vcc (+35V to +55V) | | +---------------------+---------------------+ | | | | C3 (100µF) C1 (1000µF) | | (Bootstrap) | (Decoupling) | | | | STK413-430 IC (Top View) | | +--+--+--+--+--+--+--+--+--+--+--+--+ | | |1 |2 |3 |4 |5 |6 |7 |8 |9 |10|11|12| | | +--+--+--+--+--+--+--+--+--+--+--+--+ | | | | | | | | | | | | | | | | | | | | | | | | | | | +-----+ to C3 (+) | | | | | | | | | | | | | | | | | | | | | | | | +-----------+ (Bootstrap) | | | | | | | | | | | | | | | | | | | | | +---------------- Output L | | | | | | | | | | | | | | | | | | | +----------------- -Vcc (-35V) | | | | | | | | | | | | | | | | | +-------------------- Output R | | | | | | | | | | | | | | | +----------------------- +Vcc (Power) | | | | | | | | | | | | | +-------------------------- Input R (+) | | | | | | | | | | | +----------------------------- Input R (-) / FB | | | | | | | | | +-------------------------------- Ground | | | | | | | +----------------------------------- Input L (-) / FB | | | | | +-------------------------------------- Input L (+) | | | +----------------------------------------- Ground (Signal) | +-----> Input L (+) via 1µF cap & 22k resistor +Vcc | +-----+-----+ | | | C1 C2 C3 100µF 0.1µF 100µF | | | +-----+-----+-------+ | | R3 (47Ω) | | | +----+ | | | | +-------+ | | | | | | R1 (22k) | | | STK IC | | | | Input L (+) o---[1µF]----+-------+ | +---Pin 1 | | R2 (1k) | | Ground o---------------------------+----+---Pin 3 (GND) Pin 12 (Bootstrap) ------------------------C3 (+)----+ | Pin 10 (Output L) --------------------+--------+ | | | | R4 (4.7Ω) | | | | +--------+ | | | | C4 (0.1µF) | | | | +--------+----+--- to Speaker (+) | Speaker (8Ω) | Ground 4. Key Component Values (Typical) | Component | Value | Function | | :--- | :--- | :--- | | C1, C2 | 100µF – 1000µF (≥ Vcc) | Main power supply filtering | | C3 | 100µF (≥ Vcc) | Bootstrap capacitor (pin 12) | | C4 | 0.1µF – 0.47µF | Output Zobel network capacitor | | R1 | 22kΩ – 47kΩ | Input impedance / bias resistor | | R2 | 1kΩ – 2.2kΩ | Feedback network (sets gain) | | R3 | 47Ω – 100Ω | Bootstrap resistor | | R4 | 4.7Ω – 10Ω (2W) | Output isolation / Zobel network resistor | | R5 | 47kΩ | Feedback to ground (internal or external) | | Input Cap | 1µF – 4.7µF (film or bipolar) | DC blocking capacitor | 5. Gain Calculation The closed-loop voltage gain is set by the feedback network: Always verify against your IC's specific datasheet